Innovative RF Direct Sampling System
Whether it is poor band conditions, or battling to pick out a call in a large pile-up, faint signals have always been a challenge for DXers and Contesters around the world. The difference between putting the QSO in the log or having to try another time is the capability of your receiver. One key factor is the RMDR capabilities, the ability to pick out a faint signal in the presence of stronger, adjacent signals. The IC-7610 introduces dual RF direct sampling receivers, achieving 110dB RMDR, rivaling that of top-of-the-line transceivers.
110 dB* RMDR
The RF Direct
Sampling System in the IC-7610 is capable of 110 dB RMDR. This performance
gives you the ability to pull weak signals out of the noise of strong adjacent
signals. There is a difference you can actually hear as the desired signal
comes out of the pileup!
value at 2 kHz frequency separation (Received frequency: 14.2 MHz, Mode: CW, IF
BW: 500 Hz)
VCXO Is Used for the Master Clock
noise in a receiver is always a challenge as it is a natural characteristic of
a receiver. The master clock of the IC-7610 utilizes a low phase noise VCXO
(Voltage Controlled Crystal Oscillator), combined with Icom’s years of
technical expertise to design a common power supply for the VCXO and FPGA,
yielding an ultra-low phase noise. Also, a 10 MHz reference signal can be input
to the IC-7610 for higher precision.
Independent Dual Receiver
Whether listening to both sides of a rare DX station running split, or looking for a multiplier on a different band or mode, the dual receivers in the IC-7610 have you covered. Two separate DIGI-SEL preselectors, two separate Band Pass Filter networks, feed two separate A/D converters into the FPGA.
DIGI-SEL for Main and Sub Bands
The DIGI-SEL preselectors are RF filters with sharp, narrow passband characteristics preventing Analog-to-Digital Converter overflow from large out-of-band signals when sampling the RF signals. Additionally the third and higher order IMD components are reduced. This is ideal when strong signals are received in a contest pile-up or from broadcast stations on adjacent frequencies or bands.
a) BPF and preselector passband characteristics receiving on 7.22 MHz
b) Passband characteristics between the antenna and the preselector (at the preselector output)
High Quality Speaker Sound
To finish out the receiver, is an internal speaker cabinet. The cabinet is tuned to reproduce clear, natural sounding audio, and is insulated from the radio chassis to prevent noise from vibration and panel resonance. .
Digital-Up-Conversion (DUC) for Clean TX
Breaking with the tradition of mixing a carrier signal with a local oscillator, a Digital-Up-Conversion (DUC) method is used to generate the required signal from the Digital-to-Analog Converter. The chart to the right shows the difference made by this new design.
EBuilt-in Automatic Antenna Tuner
The built-in automatic antenna tuner memorizes its settings based on your transmit frequency, so that it can recall the tuning setting when you switch operating bands. The emergency tuner function* enables you to operate for short periods of time with an antenna with a high SWR.
*Output power not guaranteed and power may be reduced.
7-inch Color Display with Touch Screen Function
The large 7-inch color display shows various operating and setting information at a glance in high resolution (800 × 480 pixels.) The display clearly shows various features, for example the dual spectrum scope aligned vertically or horizontally, simulated analog meters and RTTY, PSK31/63 mode decoded messages.
Dual Receivers, Dual Spectrum Scopes
The IC-7610 provides dual reception, on different bands, as does the high-speed, high-resolution spectrum scopes. Whether watching for a band opening, working a rare DX station operating split, or searching for a multiplier, the ability to watch each receiver separately allows the operator to concentrate on pulling in a weak signal. The scopes provide class-leading performance in resolution, sweep speed and a 100 dB dynamic range. To navigate around the band easier, connect a PC mouse to the USB port for point and click tuning of the receivers.
*Number of pixels shown at the 60 dB level, when receiving a signal.
Audio Scope Flexibility
The Audio Scope screen shows both a FFT scope with waterfall along with an oscilloscope for both transmit and receive audio. This makes it easy to monitor AF characteristics such as microphone compressor level, filter width, notch filter, and in CW, you can monitor received CW keying wave forms.
Touch Screen and Multi-Dial Knob for Smooth Operation
The combination of the touch screen and the multi-dial knob offers quick and smooth operation. When you push the multi-dial knob, menu items are shown on the right side of the display. You can select an item by touching the screen and can adjust the levels by turning the multi-dial knob.
Remote Encoder for Second VFO Knob
The optional RC-28 remote encoder enables you to add an external Sub dial for controlling the Sub band. Main band and Sub band can be switched with the F1 and F2 buttons and can be controlled with the RC-28. The LED above the F1 and F2 buttons turns ON to show the active band.
DVI-D Connector for an External Display Connection
The IC-7610 has a DVI-D connector for an external display. Operating frequency, setting information and spectrum scope can be observed on a large external display.
SD Card Slot and USB Port for Saving Data
When used with an SD card or USB flash drive, various contents including firmware updates, memory channels, captured screen images, and other personal settings, can be saved and loaded. TX/RX audio, voice memories, RTTY/CW memories and RTTY decode logs can be saved and used on the SD card.
I/Q Signal Output
The IC-7610 can output I/Q signals to a connected PC. Using the I/Q signals on the HDSDR (freeware), you can listen to received signals, or observe the spectrum scope on the PC. Used in combination with the CW Skimmer (Shareware) or N1MM Logger+ (Freeware), you can virtually decode all Morse signals in the operating band. This function is very useful for contesting and DX hunting, such as monitoring the activity in the band, and effective callback in split operation.
*The function is only available for a future firmware update
VSimplified Remote Control for RS-BA1
Whether from a remote part of your home QTH, or on a remote location somewhere around the world, the RS-BA1 software enables you to operate your IC-7610. Not only can you control the radio settings and have both RX/TX audio paths, you are able to display a single band spectrum scope with the waterfall. With the addition of an Ethernet connector, a base station computer is not required. .
Other Outstanding Features
BNC type RX IN/OUT connectors for a receiver antenna or external BPF/preamp connection
FPGA-controlled CW keying waveform shaping
Multi-function electronic keyer
CW pitch control from 300 Hz to 900 Hz
Auto repeat function
Contest serial number counter
Normal or short Morse number style
Double key jack system
Full break-in and semi break-in
CW auto tuning
APF (Audio Peak Filter) function adjustable filter shape, width and AF level
30 kHz to 60 MHz receiver
(Some frequencies are not guaranteed.)
Two types of preamplifiers
Preamp 1: Improves intermodulation characteristics
Preamp 2: High gain preamplifier
3 dB – 45 dB variable attenuator
IP+ function improves 3rd order intercept point performance
101 memory channels
RTTY encoder and decoder
Twin peak audio filter for the RTTY mode
Adjustable AGC time constant from 0.1 to 6 seconds
Digital twin PBT eliminates interference from adjacent signals
Main/Sub band tracking function for diversity reception
TX monitor function
All mode power control
VOX (Voice Operated transmission) capability
BNC type transverter connector
Microphone equalizer and adjustable transmit bandwidth
50 CTCSS tones
Memo pad stores up to 10 operating frequencies and modes
Quick split function
Quick Dualwatch function
RF gain and squelch control with a knob
RIT and ΔTX variable up to 9.999 kHz
UTC/local clock and timer function
1 Hz pitch tuning and display
Dial lock function
Adjustable main dial brake
External speaker jacks for Main and Sub receivers
Screen saver function
(S-meter, Power, ALC, COMP, SWR, ID, VD and TEMP)
Auto tuning step function
Supplied accessories (May differ depending on version)
- Hand microphone, HM-219
- DC power cable
About the 60 meter band (5 MHz)
Since the beginning of 2017, the 60-meter band (5 MHz) has been released for amateur radio in Germany. If you want to expand your Icom HC Transceiver IC-7610 for this area, please kindly contact one of our amateur radio retail partners (D/A/CH). They are informed about the possible procedure and can make the appropriate modification. And if carried out properly, the device warranty will not be affected.
Further information can be found in the download area